Significantly simpler synchronous square wave circuit for frequency division by even numbers

8-bit synchronous counter divides a frequency counter’s chip count down to 2.
Some weeks ago, EDN published my Design Idea for a square-wave output 100:1 frequency divider requiring only two chips. It prompted some interesting reader comments.
Some folks expressed concern that the asynchronous design, shown in Figure 1, suffers from questionable reliability. Their criticism was credible because the design does rely on timing relationships that, while solidly plausible, are still not explicitly guaranteed by the almighty datasheet.

Figure 1 The datasheet doesn’t guarantee that the reset pulse from U2 pin 6 to U1 pin 2 will always be long enough to reliably clear U1a.
Wow the engineering world with your unique design: Design Ideas Submission Guide
The consensus was that a synchronous design could better adhere to datasheet margins and thus embody better engineering practice and inspire (and deserve) greater confidence.
Fair enough.
But the downside was that synchronous designs also seemed likely to increase circuit complexity. I didn’t really like that, so I scratched around until I found an alternative.
Figure 2 shows the result: a design incorporating a (very) legacy yet (very) capable device, the SN74ALS86x 8bit bidirectional synchronous counter, that evades both the complexity and asynchronicity complications. It implements division ratios up to and exceeding 200:1, produces the desired 50:50 square wave output, and still requires just two chips.

Figure 2 This synchronous divider reliably implements many useful even number ratios between 2 and 242.
Here’s how it works.
As described in the 867/869 datasheet (PDF), U1 is an 8-bit up/down counter with a single synchronous clock input. Positive-going edges of the clock increment, decrement, or parallel-load the counter according to the state of the four mode control bits: S0, S1, -ENT, and –ENP.
Figure 2’s circuit enables U1 to count up until a terminal state is detected by U2a. Then U2 pin 6 goes to zero, enabling U1’s parallel load, which makes two interesting things happen on the next positive-going clock edge.
- Bits A through G are reset, beginning a new counting cycle. The connections between U1’s 7 lower order outputs and U2a’s inputs (see examples in Table 1 below) will determine the division ratio. Additional ratios can be implemented by connecting selected U1 inputs to +5 instead of ground.
- Due to the logic inversion supplied by U2b, bit H is loaded with its previous complement, thus toggling it once every counting cycle and resulting in the promised 50:50 square wave.
Obviously, with only four bits participating in U2a’s decode of U1’s 7-bit state, not all 128 theoretically possible division ratios combinations can be detected and used.
But many of them can be. Table 1 shows several useful examples.
| Division ratio | Implementation connections |
|---|---|
| Divide by 2 = 2 * (0 + 1) | +5 to J, K, L, and M |
| Divide by 10 = 2 * (4 + 1) |
Qc to J |
| Divide by 48 = 2 * ( 16 + 4 + 2 + 1 + 1) |
Qa to J |
| Divide by 100 = 2 * ( 32 + 16 + 1 + 1) |
Qa to J |
| Divide by 200 = 2 * ( 64 + 32 + 2 + 1 + 1) |
Qa to J |
Table 1 Five examples of U1 — U2 connections that implement selected division ratios.
The moral of the story: sometimes a little insurance is a good thing, so long as the premium isn’t too high.
Stephen Woodward‘s relationship with EDN’s DI column goes back quite a long way. Over 200 submissions have been accepted since his first contribution back in 1974. They have included best Design Idea of the year in 1974 and 2001.
Related Content
- Significantly simpler square wave circuits for frequency division by even numbers
- Frequency division by any even number, with a 50% duty cycle output
- A 50 MHz 50:50-square wave output frequency doubler/quadrupler
- Frequency divider from 1 to 4096 in increments of 1
The post Significantly simpler synchronous square wave circuit for frequency division by even numbers appeared first on EDN.


