• Become a member
  • Log In
The Institution of Electronics
  • Home
  • About us
    • Our Objectives
    • Our History
    • Governance of the Institution
  • The Electron Magazine
    • 2024
      • 2024 – Winter
      • 2024 – Spring
      • 2024 – Summer
      • 2024 – Autumn
    • 2025
      • 2025 – Winter
      • 2025 – Spring
      • 2025 – Summer
      • 2025 – Autumn
    • 2026
      • 2026 – Winter
      • 2026 – Summer
  • Members
    • Membership Grades and Fees
    • Members’ Resources
      • The Electron Newsletter
      • The Archives
  • Education and Projects
    • National Electronics Competition
    • Student Members’ Projects
    • Arkwright Engineering Scholarships
  • News
  • Contact Us
  • Menu Menu
Uncategorised

How microchannel liquid cooling trims electronic designs

Compact electronics present a unique challenge when it comes to cooling. While thermal management is becoming a growing concern amid increased chip functionality, smaller devices mean there’s less room for conventional heatsinks. And recent breakthroughs in microchannel liquid cooling could change that.

Fluids are 50 to 1,000 times more efficient than air at transferring heat, but the necessary infrastructure is often too large for small Internet of Things (IoT) gadgets. So, advances in precision manufacturing mean liquid heatsinks are smaller than ever before. Some cold plates are as small as 2 cm x 2 cm while dissipating up to 1,000 watts per square centimeter.

Microchannel liquid cooling facilitates more compact device form factors. Source: Sinda Thermal Technology

Such performance comes from a combination of innovative materials and a network of microchannels—fluid channels just a few microns across—that enable small-scale liquid cooling. On-chip cooling takes this potential further. Manufacturers can etch microchannels directly onto the semiconductor substrate, bringing thermal fluids as close as possible to the chip. The design minimizes losses from radiated heat and enables more compact device form factors.

Research shows on-chip liquid heatsinks exhibit 50 times greater cooling performance than conventional microchannels. Such designs also use water as the fluid. Consequently, device manufacturers could see even greater improvements using on-chip microchannels with chemical coolants.

Stacked components

The advent of on-chip microchannel liquid cooling paves the way for other optimizations. Component stacking is among the most promising of these. Removing the need for bulkier cooling infrastructure makes it possible to stack components instead of placing them next to each other without risking excessive heat.

This packaging technique reduces signal latency to improve performance and enables even more compact circuit designs. Manufacturers could use it to their advantage to overcome conventional barriers related to dark silicon.

Future challenges and considerations

A few remaining obstacles may hinder progress for microchannel liquid cooling. Manufacturing costs and complexity are the most prevalent. As effective as these solutions are, etching microscopic channels into sensitive components is inherently risky and difficult. Moreover, doing so at scale may require factories to upgrade to newer micromachining equipment, which could impact the cost-effectiveness of new devices.

However, as this technology matures, its expenses will fall. In the meantime, device manufacturers can take matters into their own hands instead of looking for a semiconductor fab that offers such cooling systems. Studies have found it’s possible to achieve a 44.4% reduction in thermal resistance by etching channels into off-the-shelf consumer-grade chips.

As microchannels enable higher functionality at lower temperatures, the industry may eventually face another challenge. Once thermal constraints no longer hold chip performance back, power delivery might. So, manufacturers could come to the point of designing chips so powerful that powering them is no longer cost-effective.

Such a conflict is likely far away, and new energy delivery technologies could emerge to address it in the meantime. However, the possibility deserves attention. Electronics manufacturers should consider these long-term implications and seek potential solutions as they capitalize on microchannel liquid cooling.

As gadgets keep getting smaller, cooling techniques will have to evolve. Here, etching microchannels directly onto the substrate is a promising solution, especially when combined with component stacking. While some challenges remain, electronics manufacturers can gain a lot by considering these methods and learning to implement them.

Ellie Gabel is a freelance writer as well as an associate editor at Revolutionized.

 

 

Related Content

AI Heats Up Data Center Cooling
Heat Removal with Microchannel Heat Sinks
IBM, GIT demo 3D die with microchannel cooling
Dutch Liquid Cooling Startup ‘Turbocharges’ Gigabyte Servers
Temperature-Monitoring Systems Optimize Cooling in Power Designs

<!–
googletag.cmd.push(function() { googletag.display(‘div-gpt-ad-native’); });
–>

The post How microchannel liquid cooling trims electronic designs appeared first on EDN.

16 September 2024
http://institutionofelectronics.ac.uk/wp-content/uploads/2022/12/IOE_LOGO.png 0 0 http://institutionofelectronics.ac.uk/wp-content/uploads/2022/12/IOE_LOGO.png 2024-09-16 09:07:242024-09-16 09:07:24How microchannel liquid cooling trims electronic designs

Latest news

  • Significantly simpler synchronous square wave circuit for frequency division by even numbers18 November 2026 - 13:16
  • Audio AI in wearables: Enabling smarter, more responsive devices18 November 2026 - 10:10
  • In-space MOSFET failure mitigation17 November 2026 - 13:57
  • Capacitor ESR challenges high-current, fast-transient power sources17 November 2026 - 10:55
  • Building AI SoCs with a continuous hardware verification strategy17 November 2026 - 06:53
  • Inspecting a DOCSIS 3.1 cable modem’s internals: Part 116 November 2026 - 13:40
  • The shocking science (and art) of plastic welding16 November 2026 - 06:33
  • Physical AI: Where AI meets the physical world13 November 2026 - 14:36
  • The tchotchke13 November 2026 - 13:33
  • Google’s Fitbit Air: Another display-less option for tech you wear12 November 2026 - 13:11
IOE LOGO 2

Become a member

click here

Become a member

click here

Become a subscriber

click here

Become a sponsor

click here

© Copyright - The Institution of Electronics | Website by WHD Solutions
  • Link to LinkedIn
  • Link to Facebook
  • Link to X
Link to: AI algorithms on MCU demo progress in automated driving Link to: AI algorithms on MCU demo progress in automated driving AI algorithms on MCU demo progress in automated driving Link to: Switch mode hotwire thermostat Link to: Switch mode hotwire thermostat Switch mode hotwire thermostat
Scroll to top Scroll to top Scroll to top