• Become a member
  • Log In
The Institution of Electronics
  • Home
  • About us
    • Our Objectives
    • Our History
    • Governance of the Institution
  • The Electron Magazine
    • 2024
      • 2024 – Winter
      • 2024 – Spring
      • 2024 – Summer
      • 2024 – Autumn
    • 2025
      • 2025 – Winter
      • 2025 – Spring
      • 2025 – Summer
      • 2025 – Autumn
    • 2026
      • 2026 – Winter
      • 2026 – Summer
  • Members
    • Membership Grades and Fees
    • Members’ Resources
      • The Electron Newsletter
      • The Archives
  • Education and Projects
    • National Electronics Competition
    • Student Members’ Projects
    • Arkwright Engineering Scholarships
  • News
  • Contact Us
  • Menu Menu
Uncategorised

Long delay timer sans large capacitors

There are several applications at home or industry for long delay timers (ON or OFF delay). Time delays on the order of seconds can be generated using 555 timer circuits, provided the timing capacitor values do not exceed the limit specified by 555 datasheets. When the time delay needed goes to minutes and hours, these circuits will not help.

Wow the engineering world with your unique design: Design Ideas Submission Guide

Figure 1’s circuit can generate time delay of seconds to hours without using high value capacitors. This simple, inexpensive circuit is basically an oscillator, divide by 4096 counter and followed by another divide by 10 circuit. The equation below can be used to obtain the time delay in seconds. The circuit draws very little current and is therefore suitable for battery powered gadgets.

Time delay = (4096X10)/F

Where F is the U1 (555) oscillator frequency in Hz.

Figure 1 The above circuit produces an OFF delay of 30 minutes. The switch SW1 can be thrown on the other side at starting to get a 30 minute ON delay. The capacitor C2 can be changed to get various timings. The required load can be connected in place of LED D1.

Circuit in Figure 1 generates a time delay of 25 minutes for the component values selected. In one position of switch SW1, an “ON” delay is generated. In another position, an “OFF” delay is generated. The load can be connected between Q1 and the power supply (across LED + R6), which can be switched “ON” or “OFF” after the time delay. U1 (555) is connected as an astable multivibrator where its output is given to U3 (4020 counter), its Q12 output is fed to U4 (4017counter and decoder). U4’s Q9 output goes “High” (up until this point, it was “LOW”), after receiving 10 cycles from Q12 of U3. It is inverted by U2C and given to U2A. This “LOW” output inhibits pulses reaching U3 causing the counters to stop after the required time delay. The Q9 output of U4 and output of U2C are connected to the SW1 switch to select an “ON” delay or “OFF” delay mode. In “ON” delay mode, the load/LED gets energized after the time delay. In “OFF” delay mode, the load / LED is energized as soon as timer is switched “ON” and gets de-energized after the time delay.

Jayapal Ramalingam has over three decades of experience in designing electronics systems for power & process industries and is presently a freelance automation consultant.

Related Content

Design low-duty-cycle timer circuits
555 timer draws zero off current
Inductor-based astable 555 timer circuit
RLD-based astable 555 timer circuit
A long pulse detector circuit
Single phase mains cycle skipping controller sans harmonics
Microcontroller’s single I/O-port line drives a bar-graph display

<!–
googletag.cmd.push(function() { googletag.display(‘div-gpt-ad-native’); });
–>

The post Long delay timer sans large capacitors appeared first on EDN.

23 September 2024
http://institutionofelectronics.ac.uk/wp-content/uploads/2022/12/IOE_LOGO.png 0 0 http://institutionofelectronics.ac.uk/wp-content/uploads/2022/12/IOE_LOGO.png 2024-09-23 15:45:572024-09-23 15:45:57Long delay timer sans large capacitors

Latest news

  • Capacitor ESR challenges high-current, fast-transient power sources17 November 2026 - 10:55
  • Building AI SoCs with a continuous hardware verification strategy17 November 2026 - 06:53
  • Inspecting a DOCSIS 3.1 cable modem’s internals: Part 116 November 2026 - 13:40
  • The shocking science (and art) of plastic welding16 November 2026 - 06:33
  • Physical AI: Where AI meets the physical world13 November 2026 - 14:36
  • The tchotchke13 November 2026 - 13:33
  • Google’s Fitbit Air: Another display-less option for tech you wear12 November 2026 - 13:11
  • MCU revitalizing SDVs with diverse compute, virtual prototyping12 November 2026 - 12:10
  • Automotive LED driver advances animated lighting11 November 2026 - 21:59
  • Isolated gate drivers serve power-switching needs11 November 2026 - 21:59
IOE LOGO 2

Become a member

click here

Become a member

click here

Become a subscriber

click here

Become a sponsor

click here

© Copyright - The Institution of Electronics | Website by WHD Solutions
  • Link to LinkedIn
  • Link to Facebook
  • Link to X
Link to: Overcoming challenges in dynamic electronics design landscape Link to: Overcoming challenges in dynamic electronics design landscape Overcoming challenges in dynamic electronics design landscape Link to: The life and chip works of Marvell co-founder Sehat Sutardja Link to: The life and chip works of Marvell co-founder Sehat Sutardja The life and chip works of Marvell co-founder Sehat Sutardja
Scroll to top Scroll to top Scroll to top